×
Quick Equipment Search
Equipment Fliter










used search tag

We are hiring! Run with Riesterer and Schnell: Apply Today

Search

S790 COMBINE

Combine

  • Combine Advisor™ package helps to set, optimize and automate combine functions when conditions change
  • Spacious and comfortable cab with everything you need to easily control your harvest right at your fingertips
  • Continued quality manufacturing of S-Series combines maximizes uptime and productivity



View Product Brochure



Features



ActiveYield delivers automatic yield calibrations to the operator without spending time manually performing yield calibrations.

Feature benefit:

  • Simplified yield calibrations for improved uptime in the field
  • Simplified data collection for use during and after harvest
#

Functionality:

ActiveYield eliminates time-consuming manual yield calibrations and replaces them with automated sensors that calibrate the machine by measuring the grain as the tank fills. This enables decisions to be made in real time without leaving the cab.

ActiveYield sensors in grain tankActiveYield sensors in grain tank

When the ActiveYield option is enabled and the Terrain Compensation Module (TCM) in the StarFire™ 3000 or StarFire 6000 Receiver has been calibrated, ActiveYield is ready to go to work. As grain is harvested and enters the tank, the three sensors within the grain tank collectively measure the grain as it piles over the cross auger covers. If all conditions are acceptable (header and separator on, grain is flowing, and machine level is within 4 degrees) load collection occurs from 900 through 3000 kg (2000 through 6600 lb).

Any pitch and roll of more than 4 degrees from center during load collection will cause the system to reject that load due to the grain pile shifting in the tank. A new calibration load starts once grain is below the sensors on the cross auger covers.

Stored calibration loads are replaced by new ones as the system continues to collect data. The system may be disabled at any time by accessing the moisture setup page and unchecking the ActiveYield box if manual yield calibration is desired.

ActiveYield calibration locationActiveYield calibration location
ActiveYield InformationActiveYield Information

ActiveYield is available for model year 2016 through model year 2019 S760, S770, S780, and S790 Combines and requires the 4600 CommandCenter™ Display, GreenStar™ 3 2630 Display, or GreenStar 3 CommandCenter. Additionally, a StarFire 3000 or 6000 Receiver must be installed on the combine with the TCM calibrated for ActiveYield to detect machine pitch correctly. Manual yield calibration is not required as each crop has a built-in default value.

Harvest Doc™ system yield data collected by an ActiveYield system is only compatible with the John Deere Operations Center. John Deere does not guarantee compatibility of ActiveYield collected documentation with John Deere APEX™ software or third-party software systems.

#

Combine Advisor is a suite of technologies designed to maximize harvesting profits. The features help the operator set and optimize the S700 Combine and then automates the combine to maintain performance target as conditions change. Purchasing Combine Advisor grants access to the Combine Advisor application, which houses three automation technologies: HarvestSmart™ system for automation of feed rate, Active Terrain Adjustment™ system for terrain change management, and Auto Maintain with ActiveVision™ cameras for crop condition change management.

Combine Advisor also provides easy navigation of the S700 set and optimize features: harvest settings application for initial set up and setting storage, VisionTrak system for monitoring losses, and Optimize Performance for step-by-step guidance of combine setting optimization. Once John Deere Combine Advisor is set into motion, the operator will experience ease-of-use benefits coupled with increased productivity.

 

Code

Description

1962

 

Combine Advisor

Base features, plus Active Terrain Adjustment and Combine Advisor. Includes ActiveVision cameras.

 

Base features include Optimize Performance, TouchSet™ system, VisionTrak, HarvestSmart, and engine speed management. HarvestSmart and engine speed management only included with code 2020 (ProDrive™ transmission). Engine speed management only available with Final Tier 4 (FT4) engines.

Combine Advisor hardware and software

Combine Advisor bundles are available for model year 2018 and future models. The bundles include ActiveVision cameras, harnesses, Auto Maintain, and software.

Dealer installation instructions are included, as weldments and drilling are required. The process will most likely take around 10 hours of labor.

Bundle

Description

BXE11034

Combine Advisor retrofit bundle for S760 and S770 Combines

Also requires BXE10948 Active Terrain Adjustment bundle if the combine is not already equipped with code 1961 (base features + Active Terrain Adjustment)

BXE11035

Combine Advisor retrofit bundle for S780 and S790 Combines

Also requires BXE10948 Active Terrain Adjustment bundle if the combine is not already equipped with code 1961 (base features + Active Terrain Adjustment)

Combine Advisor retrofit bundle componentsCombine Advisor retrofit bundle components
ICA2 run page, model years 2018 and 2019ICA2 run page, model years 2018 and 2019
Combine Advisor run page changes beginning with model year 2020Combine Advisor run page changes beginning with model year 2020
ICA2 run page, model year 2018Combine Advisor run page, model year 2020
Section A (yellow highlight): takes the operator to the current settings for concave clearance, rotor speed, fan speed, chaffer clearance, and sieve clearance, giving quick access to critical combine adjustments.Section A (yellow highlight): takes the operator to the current settings for concave clearance, rotor speed, fan speed, chaffer clearance, and sieve clearance, giving quick access to critical combine adjustments. It also shows the currently selected preset.
Section B (blue highlight): the Optimize Performance button helps the operator optimize combine performance.Section B (blue highlight): the Optimize Performance button helps the operator optimize combine performance.
Section C (pink highlight): the HarvestSmart system automates ground speed control during harvest to maintain a constant crop load.Section C (pink highlight): the HarvestSmart system automates ground speed control during harvest to maintain a constant engine load. The Manage Target with Grain Loss setting enables an automatic target adjustment based on loss levels.
Section D (orange highlight): the Active Terrain Adjustment system produces better grain quality and fewer losses while controlling tailings volume when harvesting up and down hills.Section D (orange highlight): the Active Terrain Adjustment system produces better grain quality and fewer losses while controlling tailings volume when harvesting up and down hills.
Section E (green highlight): automation statusSection E (green highlight): Combine Advisor system – HarvestSmart, Active Terrain Adjustment, and Auto Maintain.
Section F (red highlight): Auto Maintain monitors the combine and makes adjustments to maintain the performance at the operator-set performance target.Section F (red highlight): Auto Maintain monitors the combine and makes adjustments to maintain the performance at the operator-set performance target.
Section G (purple highlight): Auto Maintain also uses the buttons in section G to allow a glimpse into live views of the clean grain and tailings elevators and allows operators to use an analyzer function to see what Auto Maintain is seeing. It also shows a list of adjustments made by Auto Maintain and Active Terrain Adjustment.

**In sections C, D and F select the screen area to see additional sensitivity settings for each system.
Section G (purple highlight): Auto Maintain also uses the buttons in section G to allow a glimpse into live views of the clean grain and tailings elevators and allows operators to use an analyzer function to see what Auto Maintain is seeing. It also shows a list of adjustments made by Auto Maintain and Active Terrain Adjustment.

**In sections C, D and E select the screen area to see additional sensitivity settings for each system.
Section H (brown highlight): indicates the operator’s priorities for automation---

 

  • The automation features are highly dependent on the quality of the performance target sets. There are three ways an operator can achieve an optimal target:
    • Use existing operator knowledge and experience
    • Utilize Optimize Performance
    • Work with a dealer support team
  • Combine Advisor has been available as a factory-installed option since model year 2018 combines.
  • Auto Maintain is compatible for corn, soybeans, wheat, canola, and barley.
  • HarvestSmart is included only with ProDrive transmission code 2020.
  • Active Terrain Adjustment is an optional feature that is orderable with codes 1961 or 1962.
  • Auto Maintain must have Active Terrain Adjustment in order to work.
Historical Auto Maintain performance graphHistorical Auto Maintain performance graph

The ActiveVision cameras can detect broken and unthreshed grain. The cameras will also detect lightweight and heavy foreign material to make the appropriate combine settings changes. The system provides a live feed of both the grain and tailings cameras and will highlight the parameters outlined to make it easier to analyze. The live view and historical graphs update constantly, and the cameras will even tell the operator if there is debris on the lens.

Grain analysis live viewGrain analysis live view

Combine Advisor with Auto Maintain is available as a factory-installed option on combines since model year 2018. Auto Maintain is compatible in corn, soybeans, wheat, canola, and barley. Retrofit kits, BXE11034 and BXE11035 are available. Please refer to that section for more information. 

Combine Advisor video
Combine Advisor application
Combine Advisor run pageCombine Advisor run page

The Combine Advisor application provides the tools needed to set the combine to get the most out of it and automatically adjust settings to maintain optimum performance. Inside this application on the 4600 CommandCenter™ Display, the operator will find many tools including easy-to-adjust current machine settings, sensitivity settings for automation, application status indicators, automation activity history overviews, and live feeds of grain analysis cameras.

Additionally, the operator can access Optimize Performance, activate the three automation technologies, and set the performance targets the machine will automatically adjust to maintain.

Feature benefits:

  • Efficient combine operation with a one-page application for animation technologies
  • Improved combine settings management with settings, sensitivities, and status information all on one reference page
  • Reduced operator training and efficient, easy control of harvest settings through an intuitive run page and user interface

Functionality:

Auto Maintain

Auto Maintain with ActiveVision cameras is technology that works to automatically adjust five primary S700 Combine settings to maintain the user set performance target. When harvesting corn, soybeans, wheat, canola, or barley, the combine will maintain the performance of everything from grain loss and grain quality, to foreign material in the grain tank. The ActiveVision cameras, along with grain loss monitors, are specifically designed to identify the impact of crop condition changes and adjust the combine to maintain the performance target, allowing the operator to focus on other challenges of harvest.

Feature benefits:

  • Simplify harvest by automating the critical workload of constantly managing combine settings when conditions change

  • Increase productivity by allowing ActiveVision cameras to identify and address tough-to-spot problems such as cracked grain

  • Provide flexibility in planning overall business and increase the efficiency of the combine independent of operator experience

Combine Advisor run pageCombine Advisor run page

Functionality

Auto Maintain looks at the level at which the combine is performing, sets that as the goal, and automates combine settings to continually hit the target performance goal over time. Auto Maintain uses existing sensor inputs along with the ActiveVision cameras to make decisions for accurate combine adjustments. It does not use grain moisture as an input, however. Auto Maintain is able to hit the target goal by automatically making adjustments to the threshing speed, concave clearance, chaffer clearance, sieve clearance, and fan speed. The ActiveVision cameras have been trained to analyze the clean grain and tailings material and input that analysis into the Auto Maintain system. Auto Maintain will show the operator how it has been performing with a constantly updating historical graph of losses, grain quality, and foreign material in the clean grain. The green-shaded area below indicates the performance targets set. The colored lines show the ongoing levels of losses and quality. For example, the green, purple, and orange lines below show a period of time outside of the green-shaded acceptable area. Auto Maintain recognizes this and makes the appropriate adjustments to meet the set targets.

Additional Combine Advisor features

The Generation 4 CommandCenter was designed to provide a consistent user experience by providing full-screen viewing of more run page modules, shortcut keys, and precision agriculture capabilities.

Expect easier set-up, along with increased operator confidence, thanks to a simple, customizable interface. The improved design of the Generation 4 CommandCenter also aids in an optimal operating experience and maximizes uptime.

In order to increase your efficiency, take advantage of the following features offered by the Generation 4 CommandCenter:

Layout manager
Layout manager selection pageLayout manager selection page
Layout manager module buildLayout manager module build
  • Easily create page views that meet your needs and that are also equipped with default run pages.
    • Users and access allow the owner or manager to lock out certain functions to prevent operators from accessing or changing settings with a defined four-digit code.
    • Gather on-screen help by selecting the help icon on the shortcut bar on the bottom of every page.
Machine monitor
Machine monitor pageMachine monitor page
  • The Machine Monitor application provides you instantaneous readings about the status or condition of your machine.
    • This application shows parameters such as engine speed, coolant temperature, and ground speed.
Work monitor
Work monitor pageWork monitor page
  • The Work Monitor application displays performance information about the task being performed by the machine.
    • You are shown averages, totals, and productivity of the machine, such as area worked, average working speed, and fuel usage.
    • Work setup places the settings needed to properly setup features such as AutoTrac, Documentation, and Section Control in a single location. Settings include:
      • Client, farm, and field
      • Crop type
      • Machine and implement dimensions
      • Variety/hybrid and planting/seeding rates
      • Variable rate prescriptions
      • Product and application rates
      • Application rates through the implement screens
Video capability
  • Machines equipped with a 4200 CommandCenter are equipped with one video input, and the 4600 CommandCenter has four video inputs.
    • You have the ability to set a variety of triggers. With each trigger, the image will then appear on the display.
Flags
Create flags to mark items in the fieldCreate flags to mark items in the field
  • Mark areas in the field that need special attention such as rocks, tile lines, or weed pressure.
    • Flags previously recorded on the Gen 4 or GreenStar™ 3 2630 Display can be transferred between monitors.
Field boundaries
Boundary creation from coverageBoundary creation from coverage
Headland creationHeadland creation
  • Manually drive field boundaries with the Generation 4 CommandCenter or import existing boundary information from the GreenStar 3 2630 Display or John Deere Operations Center. Gen 4 documentation data can be used to create boundaries from coverage within the John Deere Operations Center.
Dual-display mode
Dual displayDual display
  • Generation 4 CommandCenter may be configured to run with the following John Deere displays connected at the cornerpost of a John Deere tractor:
    • GreenStar 2 1800 Display
    • GreenStar 2 2600 Display
    • GreenStar 3 2630 Display
    • 4640 Universal Display
    • 4240 Universal Display

NOTE: Vehicle applications will always be located on the Gen 4 CommandCenter.

Automatic base station switching
Setup base stations in Fields and Boundaries applicationsSetup base stations in Fields and Boundaries applications
  • Customers using John Deere RTK Radio 450 or 900 can link a base station to a desired client,/ farm,/ or field. This allows automatic switching to the associated base station when changing fields. The ability to import base station assignments into Operations Center and send back to machines will be available at a later date.
Video looping supported with Gen 4 4600 CommandCenter Display and 4640 Universal Display
Scan through videos with video loopingScan through videos with video looping
  • This feature enables users to scan or loop through all of the available video feeds for a specified duration. The default scan time is set to 7 seconds per image. The scan time is customizable per image allowing for consistent visibility to all video feeds.
#

Harvest is hectic. Producers are focusing on getting all the crop from the field to the bin within a tight harvest window. Using Machine Sync, those producers can focus more on grain harvest and grain quality, and worry less about keeping the grain cart under the spout when unloading on the go. Gen 4 Machine Sync provides a solution to harvest stress by creating a wireless network between the tractor and combine to enable on-the-go unloading by synchronizing tractor speed and direction of travel with the combine.

Machine Sync works with In-Field Data Sharing to show the location of all combines and tractors within the fleet of Gen 4 machines harvesting in the field. Knowing the exact location of multiple combines as well as their grain tank fill level and unloading auger status allows the grain cart operators to be in the right place at the right time. 

NOTE: Active Concave Isolation is only available on S780 and S790 Combines.

ACI increases throughput in tough threshing small grains and rice without sacrificing overall grain savings. This system allows producers to continue to harvest outside the optimal harvest window and conditions. The concaves are suspended by hydraulic cylinders that increase the amount of crop that is being threshed as well as reduces the amount of rotor noise that is heard by the operator.

Feature benefits:
  • In tough threshing, small grains producers can see up to a 10 percent increase in machine capacity while maintaining their loss level when the combine is equipped with a tough crop packages
  • In tough material handling conditions, the tough crop packages improve the throughput of the combine up to 20 percent to better utilize true machine performance outside the optimal harvest window and conditions, while accepting increased loss levels
  • Improved drivability and ability to handle slugs
  • Enhanced durability and uptime with the elimination of sheer bolts in the system
  • Increased operator comfort with the reduction of concave banging noise
ACIACI
Functionality:

The ACI feature hydraulically suspends the concaves; the consistency of the concave gap is increased along with decreasing sensor drift for a more accurate concave distance. Material flow through the threshing section of the machine is smoother, giving more consistent threshing.

The Dyna-Flo Plus cleaning shoe is the heart of the S700 Combine cleaning system. The system is made up of a unique design consisting of aluminum and high-strength steel that reduces overall weight while maintaining overall strength. The Dyna-Flo Plus cleaning shoe also features an enhanced drive system that requires only one flywheel for optimal shoe performance and maximizes uptime.

Feature benefit:

  • Increased size of the sieve area by 12 percent for up to an additional 0.6 ha (1.5 acres) per hour of productivity.
  • Tailings volume reduction of up to 28 percent in coarse grains and up to 14 percent in small grains.
  • Weight reduction of 180 kg (396 lb) for smoother operation and reduced combine ground compaction.
Dyna-Flo Plus cleaning shoeDyna-Flo Plus cleaning shoe
Enhanced drive systemEnhanced drive system
Functionality:

The Dyna-Flo Plus cleaning system begins with conveyor augers located beneath the concave area, where the volume of threshed material is highest, to evenly move material onto the cleaning shoe (1). The deep auger troughs provide uniform distribution of material to the cleaning shoe with less bunching, even on sloping terrain and when harvesting up and down hills.

Dyna-Flo Plus cleaning shoeDyna-Flo Plus cleaning shoe

Once grain is on the cleaning shoe, the raised-center front chaffer cleans up to 40 percent of free grain before it reaches the main chaffer (3). High-velocity air from the cleaning fan elevates any light material traveling over the end of the front chaffer, resulting in more aggressive separation of chaff and increased cleaning performance (2). The main chaffer provides grain separation from chaff as the grain passes through the main chaffer to the sieve (4).

The sieve provides proper sizing of grain from material other than grain (5). Any grain that passes through the sieve is elevated to the grain tank while some grain or material other than grain flows to the tailings return system for reprocessing. On S760, and S770 Combines, the tailings material is directed back into the threshing section of the separator for additional threshing. The tailings material on the S780 and S790 Combines are directed to the active tailings return system for additional threshing, and then directed back on the return pan and then onto the main chaffer for additional cleaning (6).

Harvesting in slopesHarvesting in slopes
Harvesting in rolling groundHarvesting in rolling ground

The industry-exclusive ProDrive system uses PowerShift™ transmission technology to automatically shift between two speed ranges as ground conditions and terrain change to keep the combine harvesting at the desired ground speed.  Valuable harvest time will no longer be lost shifting on hills and when exiting fields to start transporting.

Feature benefit:

  • Precise control of the combine speed (when going up or down hills) without the need to continuously monitor and adjust the multifunction control lever
  • Retain high levels of productivity through the speed ranges with shift-on-the-go technology
  • Maintain ground speed when engaging four-wheel drive (4WD) (if equipped)
  • Operator-selected maximum speed within each range, allowing for more precise control of the combine in delicate operations (for example, when hooking up headers)

The ProDrive system on S700 Combines includes an integrated HarvestSmart™ feedrate control system to provide the maximum productivity and reduce operator stress and fatigue.

Functionality:

 

The ProDrive hydrostatic motor has a higher displacement than the previous hydrostatic systems. Both the pump and motor are variable-displacement components that allow ProDrive to maintain high levels of torque to the ground throughout each of the two operating-speed ranges.

 

Range one can be set for typical harvesting speeds. Range two can be used when higher speeds are needed during harvest or when transporting the combine.

 

The ground speed can be infinitely varied within both modes by the operator, using the multifunction control lever on the CommandARM™ armrest console. The multifunction lever regulates the high-capacity, variable hydrostatic pump and motor that drives the ground speed.

 

Using the navigation tools on the armrest, the operator can dial in the desired maximum-attainable speed within each of the two speed ranges. The maximum forward speed in either range can be set from 0 to 38.6 km/h (0 to 24 mph). The maximum speed in range one cannot be set higher than the maximum speed for range two. For example, if a maximum harvest speed of 13 km/h (8 mph) is desired and set, the full forward position of the hydrostatic control handle will deliver the speed of 13 km/h (8 mph).

 

The ProDrive transmission is equipped with an electrohydraulic differential lock with a four-pinion differential.  Non-ProDrive combines have a two-pinion differential. When operating in muddy, hilly terrain or in sandy conditions that may cause one of the tires to lose traction, this differential lock enables the operator to maintain productivity. If traction is lost, the operator can quickly and easily engage the differential lock by pressing the differential lock button on the CommandARM armrest console. An indicator light within the button alerts the operator that the differential locking feature is engaged.

The TriStream rotor is unique to John Deere because it features a slightly tapered design in the threshing area for best-in-class grain quality while dramatically reducing the growling that often comes with heavy rotor loads. The TriStream rotor is recommended for producers who harvest mainly coarse grains along with easy-threshing small grains.

The spiral vanes surrounding the rotor guide the crop material through the threshing and separating area in a pull-and-release action to improve performance. This John Deere S700 Combine feature will generate less power consumption.

 

Feature benefits:

  • TriStream rotor technology reduces the force required to move material through the combine by as much as 20 percent, maximizing fuel efficiency.
  • The rifling grooves on the threshing elements allow the bullet-shaped rotor to move material more efficiently, maximizing crop threshing performance and grain quality.
  • Heavy-duty vanes on the top covers propel the crop smoothly rearward through the length of the rotor, ensuring all the threshed grain is separated.
S700 TriStream rotorS700 TriStream rotor

Functionality:

 

Fifteen cast-constructed threshing elements provide superior material handling with excellent grain quality.  The elements spiral around the rotor to control material flow.  In some harvesting environments, the dense-pack configuration (nine additional threshing elements) may be necessary. 

TriStream threshing elementsTriStream threshing elements

Conical top covers allow for smooth material movement within the threshing and separating area. The top covers have a radius larger than the rotor, allowing the material to expand as it travels along the top of the rotor. This design uses the pull-and-release action of crop material, aiding in the threshing and separating to reduce power consumption.

Conical top coversConical top covers

The industry-exclusive variable-stream rotor features a tapered design in the threshing section, which improves crop flow, enhances grain quality, and reduces power consumption. The variable-stream rotor with adjustable top cover transport vanes is recommended for producers of rice and in tough threshing conditions.

 

The variable-stream rotor smooths crop flow during tough handling conditions to maximize throughput. Along with the tough-material handling capabilities of the variable-stream rotor configuration, the straw quality and length can be improved due to the electrically adjustable top cover transport vanes.

 

Feature benefits:

  • The longer rotor taper in the threshing area allows improved material handling by providing smoother crop flow through the combine, maximizing threshing performance and fuel efficiency.
  • Electrically adjustable transport vanes allow operators to change the vane angle from the cab for improved straw quality.
S700 variable-stream rotorS700 variable-stream rotor

Functionality:

 

Fifteen cast-constructed threshing elements provide superior handling, improved durability and serviceability, and maintain excellent grain quality. The elements spiral around the rotor to move and control the material. In some harvesting conditions, 12 additional bolt-on threshing tines may be installed for increased material handling.

 

Rear discharge flights and a tapered rear cone improve material handoff to the rear discharge beater.

 

Electrically adjustable transport vanes allow operators to change the vane angle within the cab. Longer straw length can be accomplished when vanes are in the advanced position. 

Electric actuator for adjustable vanesElectric actuator for adjustable vanes

Specifications


Compare the specifications of up to 4 models

Key Specs s790-combine
Current Model
Engine typeJohn Deere PowerTech™ PSS engine
13.5 L
824 cu in.
Rated power405 kW
543 hp
Fuel capacity1,250 L
330 gal.
Rotor length312 cm
123 in.
Rotor diameter76.2 cm
30 in.
Concave area1.1 m2
11.8 sq ft
Separating area1.54 m2
16.6 sq ft
Total cleaning area (louvered)5.9 m2
63.5 sq ft
Grain tank size14,100 L
400 bu
Unloading rate135 L/s
3.8 bu/sec
Engine
Engine typeJohn Deere PowerTech PSS engine
13.5 L
824 cu in.
Emission levelFinal Tier 4 / Tier 2 (Australia/New Zealand)
Rated speed2,100 rpm
Rated power405 kW
543 hp
Power boost @ rated speed37 kW
50 hp
Fuel capacity1,250 L
330 gal.
Engine family
Feeding
Drive typeFixed or multi-speed
Conveyor chain slat typeCast iron
Width139.7 cm
55 in.
Length172.5 cm
67.9 in.
Feed Accelerator, Stone Trap (FAST)Reverser
Standard
Standard
Threshing/ Separating
Separator typeRotary
Rotor length312 cm
123 in.
Rotor diameter76.2 cm
30 in.
Rotor speed range210-1,000 rpm
Concave area1.1 m2
11.8 sq ft
Separating area1.54 m2
16.6 sq ft
Discharge grate area0.45 m2
4.8 sq ft
Cleaning
Front chaffer0.5 m2
5.4 sq ft
Front chaffer extension0.8 m2
8.6 sq ft
Pre cleaning
Chaffer2.5 m2
26.9 sq ft
Sieve area2.1 m2
22.6 sq ft
Total cleaning area (louvered)5.9 m2
63.5 sq ft
Cleaning fan speed620-1,350 rpm
Grain handling
Grain tank size14,100 L
400 bu
Unloading auger length6.9, 7.9 or 8.7 m
22.5, 26 or 28.5 ft
Unloading rate135 L/s
3.8 bu/sec
Base weight - less head
Manufacturing location

Accessories and Attachments

Bracket

10" Tablet Holder Kit - BXE10901

12 Tablet Holder Kit (Ipad Pro) - BXE10864

Camera Observation System

The camera-ready feature is optional on all S700 Combines and provides factory-installed observation camera harnesses and brackets in the grain tank, on the unloading auger, and at the rear of the combine.

 

John Deere value:

  • Provides increased visibility options when unloading grain and maneuvering the combine in and out of the field
  • Four integrated camera views on the 4600 CommandCenter™ Display for more convenience

 

Functionality:

  • Quickly install compatible cameras, orderable from Service Parts
  • Harness and brackets are provided factory installed, cameras have to be ordered separately via Parts
Rearview camera locationRearview camera location
Unloading auger camera locationUnloading auger camera location
Unloading auger camera locationUnloading auger camera location
Grain tank camera locationGrain tank camera location
Camera trigger menuCamera trigger menu
  • Camera triggers with time menu for:
    • Reverse with separator on video trigger
    • Reverse with separator off video trigger
    • Separator video trigger
    • 3/4 grain tank video trigger
    • 4/4 grain tank video trigger
    • Trigger menu for cameras

 

NOTE: 4600 CommandCenter is capable of viewing up to four cameras simultaneously.

 

NOTE: Cameras are not included with factory-installed option. Please order cameras from Service Parts.

 

Voyager Camera - SWCVMS155B

Voyager One Camera Kit - SWVCMS155JD1

Voyager Three Camera Kit - SWVCMS155JD3

Chaffer And Sieve

3 mm Fixed Round Hole Sieve - AXE68434

The Dyna-Flo Plus cleaning shoe is the heart of the S700 Combine cleaning system. The system is made up of a unique design consisting of aluminum and high-strength steel that reduces overall weight while maintaining overall strength. The Dyna-Flo Plus cleaning shoe also features an enhanced drive system that requires only one flywheel for optimal shoe performance and maximizes uptime.

Feature benefit:

  • Increased size of the sieve area by 12 percent for up to an additional 0.6 ha (1.5 acres) per hour of productivity.
  • Tailings volume reduction of up to 28 percent in coarse grains and up to 14 percent in small grains.
  • Weight reduction of 180 kg (396 lb) for smoother operation and reduced combine ground compaction.
Dyna-Flo Plus cleaning shoeDyna-Flo Plus cleaning shoe
Enhanced drive systemEnhanced drive system
Functionality:

The Dyna-Flo Plus cleaning system begins with conveyor augers located beneath the concave area, where the volume of threshed material is highest, to evenly move material onto the cleaning shoe (1). The deep auger troughs provide uniform distribution of material to the cleaning shoe with less bunching, even on sloping terrain and when harvesting up and down hills.

Dyna-Flo Plus cleaning shoeDyna-Flo Plus cleaning shoe

Once grain is on the cleaning shoe, the raised-center front chaffer cleans up to 40 percent of free grain before it reaches the main chaffer (3). High-velocity air from the cleaning fan elevates any light material traveling over the end of the front chaffer, resulting in more aggressive separation of chaff and increased cleaning performance (2). The main chaffer provides grain separation from chaff as the grain passes through the main chaffer to the sieve (4).

The sieve provides proper sizing of grain from material other than grain (5). Any grain that passes through the sieve is elevated to the grain tank while some grain or material other than grain flows to the tailings return system for reprocessing. On S760, and S770 Combines, the tailings material is directed back into the threshing section of the separator for additional threshing. The tailings material on the S780 and S790 Combines are directed to the active tailings return system for additional threshing, and then directed back on the return pan and then onto the main chaffer for additional cleaning (6).

Parts included for side hill packageParts included for side hill package

The side hill performance package can improve combine performance on slopes up to 8 degrees (14 percent) by substantially reducing cleaning shoe grain loss to acceptable levels.

 

Feature benefit:

  • Reduces grain loss out of the rear of the combine on side hill slopes
  • Increases combine productivity by not having to slow down on side hill slopes

 

Functionality:

 

The side hill kit installed in the cleaning shoe of S700 Combines allows grain to be evenly distributed across the entire width of the shoe when harvesting in slopes. As grain moves to the rear of the combine, the dividers keep grain contained into four individual bays which prevents overloading one side of the cleaning shoe. Additionally, the rubber agitator paddles in each individual bay work with the oscillating motion of the cleaning shoe to move grain toward the center of each bay for increased utilization of the entire cleaning shoe width for increased performance and productivity.

Parts included for side hill packageParts included for side hill package

The side hill performance package can improve combine performance on slopes up to 8 degrees (14 percent) by substantially reducing cleaning shoe grain loss to acceptable levels.

 

Feature benefit:

  • Reduces grain loss out of the rear of the combine on side hill slopes
  • Increases combine productivity by not having to slow down on side hill slopes

 

Functionality:

 

The side hill kit installed in the cleaning shoe of S700 Combines allows grain to be evenly distributed across the entire width of the shoe when harvesting in slopes. As grain moves to the rear of the combine, the dividers keep grain contained into four individual bays which prevents overloading one side of the cleaning shoe. Additionally, the rubber agitator paddles in each individual bay work with the oscillating motion of the cleaning shoe to move grain toward the center of each bay for increased utilization of the entire cleaning shoe width for increased performance and productivity.

Deep Tooth Chaffer - AXE60613

Deep Tooth Sieve - For TouchSet Remote Combine Adjustment:  S760-S790 - AXE68433

General Purpose Sieve - AXE60449

Concaves And Threshing

The concave inserts provide the additional threshing action required for harvesting small grain with the round-bar/multi-crop concave.

 

Feature benefits:

  • Flexibility to harvest additional crops without having to change out concaves
  • Support bracket and latch enables quick installation and removal of the threshing insert as needed with no tools required
Round-bar/multi-crop concaves with insertsRound-bar/multi-crop concaves with inserts
Concave insert for round-bar concavesConcave insert for round-bar concaves

Functionality:

 

The concave insert assembly consists of an over-center latching mechanism, left-hand support bracket, and the threshing insert. The over-center latch and support bracket bolt to the round-bar concave and remain in place, enabling quick installation and removal of the threshing insert as needed - no tools required. These concave inserts are recommended for use with the round-bar/multi-crop concave in small-grain crops. The attachment includes a set of two inserts for use in the front concave section only.

Additional threshing tine base weldments for installation into the DensePack locations of a variable-stream rotor can only be used to improve material handling in some tougher conditions such as rice and grass seed harvest.  This may decrease machine performance if used in dry, brittle-crop conditions. 

 

Feature benefit:

  • Rice machines ordered from the factory already come with these tines installed for increased productivity and capacity
  • Increase in machine performance in tough-threshing and damp crops
Variable-stream rotor equipped with DensePackVariable-stream rotor equipped with DensePack
Grain wear platesGrain wear plates
Rice wear platesRice wear plates
#

 

Wear plate kits (grain versus rice) must be ordered separately through Service Parts.

Rear of rotor with discharge paddlesRear of rotor with discharge paddles

Rotor discharge flights are available for STS combines when operating in specialty crops. The discharge flights are recommended for use in crops such as sunflowers and edible beans when operating in conditions that require rotor threshing speeds below 300 rpm. 

 

The discharge flights are designed to provide an aggressive push to the slow-moving crop material as it moves from the rotor housing into the discharge beater. The additional kick provided by the paddle design of the flighting significantly improves material flow and reduces possible plugging at the rear of the rotor at extremely low threshing speeds.

 

When operating in other crops where rotor speeds higher than 300 rpm are required (for example, soybeans, wheat, rice, etc.), it is recommended the discharge flights BE REMOVED to ensure adequate and even material flow through the rotor, as well as to provide better residue spread.

 

IMPORTANT:  Discharge flight paddles are NOT recommended for use in heavy, damp wheat or rice crops.

 

The discharge flight is for use on any 9650 STS, 9750 STS, 9660 STS, 9760 STS, 9860 STS, 9670 STS, 9770 STS, and 9870 STS Combines and does not require the combine to be fitted with any particular configuration of rotor discharge housings.

 

NOTE: Two rotor discharge flight paddles for 9560 STS, 9570 STS, and S550 STS Combines, AH219961 and AH219962, can be ordered through Service Parts.

Extended Wear Round Bar Concaves (Set of 3) - BXE10387

Small-wire concaves are standard equipment on small-grain combines and are recommended for use in wheat, barley, and other cereal crops. The small-wire concaves are recommended for use in specialty crops such as grass seed.

 

Feature benefits:

  • Provide maximum grain quality and productivity when harvesting small grains
  • Allow versatility to harvest specialty crops such as grass seed without having to switch out concaves
Small-wire concave for small grainSmall-wire concave for small grain

 

See concave recommendations to choose the concaves that are best for grower's operation.

 

The small-wire concaves are also available as an option with boronized treatment for extended-wear life. This process penetrates the surface of the concave with a layer of hard, wear-resistant material, extending the life of the concave up to twice as long, and is available in the extended-wear separator package.

 

IMPORTANT: Not recommended for use in corn.

 

 

Large-wire concaves are standard on S700 Rice Combines and available as an option on corn and small-grain combines. They are recommended for rice, sorghum, soybeans, and corn.

 

Feature benefit:

  • Best separating performance in rice to maximize productivity
  • Versatility to perform well in soybean harvest, eliminating the need to change out concaves or purchase additional set of concaves
Large-wire concaveLarge-wire concave

Large-wire concaves are standard on S700 Rice Combines and available as an option on corn and small-grain combines.

 

They are recommended for rice, sorghum, soybeans, and corn.

 

See concave recommendations to choose the concaves that are best for grower's operation. 

 

As an option, all three sections can be boronized for extended-wear life. This process penetrates the surface of the concave with a layer of hard, wear-resistant material, extending life up to twice as long.

Large-wire concaves are standard on S700 Rice Combines and available as an option on corn and small-grain combines. They are recommended for rice, sorghum, soybeans, and corn.

 

Feature benefit:

  • Best separating performance in rice to maximize productivity
  • Versatility to perform well in soybean harvest, eliminating the need to change out concaves or purchase additional set of concaves
Large-wire concaveLarge-wire concave

Large-wire concaves are standard on S700 Rice Combines and available as an option on corn and small-grain combines.

 

They are recommended for rice, sorghum, soybeans, and corn.

 

See concave recommendations to choose the concaves that are best for grower's operation. 

 

As an option, all three sections can be boronized for extended-wear life. This process penetrates the surface of the concave with a layer of hard, wear-resistant material, extending life up to twice as long.

Rice Performance Enhancement Package - BXE10491

Concave cover plates for round-bar concaves onlyConcave cover plates for round-bar concaves only

Concave sectionalized cover plates for round-bar concaves help to increase performance in the threshing area in tough conditions and can improve material distribution from the concaves to the cleaning system.

Concave cover plates for round-bar concaves onlyConcave cover plates for round-bar concaves only

Concave sectionalized cover plates for round-bar concaves help to increase performance in the threshing area in tough conditions and can improve material distribution from the concaves to the cleaning system.

Small-wire concaves are standard equipment on small-grain combines and are recommended for use in wheat, barley, and other cereal crops. The small-wire concaves are recommended for use in specialty crops such as grass seed.

 

Feature benefits:

  • Provide maximum grain quality and productivity when harvesting small grains
  • Allow versatility to harvest specialty crops such as grass seed without having to switch out concaves
Small-wire concave for small grainSmall-wire concave for small grain

 

See concave recommendations to choose the concaves that are best for grower's operation.

 

The small-wire concaves are also available as an option with boronized treatment for extended-wear life. This process penetrates the surface of the concave with a layer of hard, wear-resistant material, extending the life of the concave up to twice as long, and is available in the extended-wear separator package.

 

IMPORTANT: Not recommended for use in corn.

 

 

Corn

Engine

110V Pump Kit - SW110VDEFSS

12V Pump Kit - SW12VDEFSS

65 gal. Portable Dispensing Unit with lockable, hinged lid - SWDEFPDU65M

Air Compressor Conversion Kit - BXE10700

Air Compressor Conversion Kit - BXE10701

The rotary screen brush kit adds a series of brushes to the rotary screen. The brushes prevent debris from building up on the screen, allowing full air flow to the engine for cooling.

Engine

275 gal. Tote of John Deere Diesel Exhaust Fluid - SWDEF275

330 gal. Tote of John Deere Diesel Exhaust Fluid - SWDEF330

55 gal. drum of John Deere Diesel Exhaust Fluid - SWDEF055

Fast (Feed Accelerator And Stone Trap)

Contoured serrated wear stripsContoured serrated wear strips
Regular straight serrated wear stripsRegular straight serrated wear strips

The serrated feed accelerator wings have a smooth contoured back to provide fast yet gentle crop handling while also featuring serrated edges for positive crop movement in viney crops such as edible beans.

 

The updated feed accelerator wings are recommended in place of the optional smooth accelerator wear strips attachment because they help to provide excellent grain quality without compromising feeding performance in edible beans.

NOTE: The standard straight serrated wear strips are still the recommended choice to use on the feed accelerator when harvesting in damp or green-stemmed-type crops.
Stone trap and stone trap handleStone trap and stone trap handle
#

The stone trap protects the combine's interior area by effectively catching stones deflected by the feed accelerator into the stone dump area before they enter the TriStream™ feed section.

  • Remote lever with an over-center latch makes cleanout fast and easy.
  • Trap requires no adjustment and provides worry-free harvesting when cutting close to the ground.
  • Adds no additional length to the feederhouse. Excellent line-of-sight visibility of the platform cutterbar is maintained.
  • No compromise in feeding material smoothly from the platform to the feederhouse conveyor chain.
  • No increase in front axle tire loading since feederhouse length is not extended.

 

Base Equipment On: S-Series Combines

 

Field-installation information

An expanded stone trap door with a two-piece front feed floor is available as a field-installed bundle. This bundle replaces the standard one-piece feed floor.

 

When harvesting crops such as corn, food corn, popcorn, and small grains, the front-piece floor section remains bolted in place. This allows 9 in. of opening across the width of the machine.

 

In rocky conditions such as beans and edible beans, the front floor section is removed to provide 11.5 in. of open area to the larger stone trap, allowing improved rock protection (22 percent increase in stone trap area).

 

Please refer to the chart below for retro-fit information

Two-speed feed accelerator handle Two-speed feed accelerator handle

The slow-speed drive reduces the standard two-speed feed accelerator from 450 rpm/800 rpm to 320 rpm/770 rpm.

 

These lower speeds allow the feed accelerator to provide more gentle grain handling in delicate specialty crops such as edible beans, food corn, or popcorn. 

 

Having the slow-speed feed accelerator drive available as a factory-installed option allows those who plan on using this drive for harvesting all their crops to save the cost of discarding the standard feed accelerator drive parts in the field.

Smooth-wear strips on feed acceleratorSmooth-wear strips on feed accelerator

The smooth-wear strips provide optimum grain quality in speciality crops such as popcorn and food corn. The bundle includes set of 30 wear strips to replace standard-equipment serrated wear strips.

Spike Feed Accelerator - BH84582

Tine Feed Accelerator - BH84416

Grain Handling

Grain tank level sensorGrain tank level sensor

The fast, easy way to let the operator know the combine’s grain tank is full when harvesting on side hills.

Feature benefits:
Beacons activatedBeacons activated
  • Improved accuracy when harvesting in hilly terrain 
  • Prevents overfilling the grain tank

 

Functionality:

 

An additional grain tank level indicator is available to help detect a full grain tank.

 

The beacon lights are also activated when the combine is in road transport mode.

Door, Extra High Capacity, Clean Grain - S690/S790 - BXE10096

Perforated and Clean Grain Doors - BH80611

Rethresher Perforated Boot Door - BXE10151

Steel Paddle Tailing Elevator for all 9770 STS, 9870 STS, S670, S680, S690, S770, S780, S790 Combines - H229907

Greenstar Brackets

Harvest Information Technology

ActiveYield delivers automatic yield calibrations to the operator without spending time manually performing yield calibrations.

Feature benefit:

  • Simplified yield calibrations for improved uptime in the field
  • Simplified data collection for use during and after harvest
#

Functionality:

ActiveYield eliminates time-consuming manual yield calibrations and replaces them with automated sensors that calibrate the machine by measuring the grain as the tank fills. This enables decisions to be made in real time without leaving the cab.

ActiveYield sensors in grain tankActiveYield sensors in grain tank

When the ActiveYield option is enabled and the Terrain Compensation Module (TCM) in the StarFire™ 3000 or StarFire 6000 Receiver has been calibrated, ActiveYield is ready to go to work. As grain is harvested and enters the tank, the three sensors within the grain tank collectively measure the grain as it piles over the cross auger covers. If all conditions are acceptable (header and separator on, grain is flowing, and machine level is within 4 degrees) load collection occurs from 900 through 3000 kg (2000 through 6600 lb).

Any pitch and roll of more than 4 degrees from center during load collection will cause the system to reject that load due to the grain pile shifting in the tank. A new calibration load starts once grain is below the sensors on the cross auger covers.

Stored calibration loads are replaced by new ones as the system continues to collect data. The system may be disabled at any time by accessing the moisture setup page and unchecking the ActiveYield box if manual yield calibration is desired.

ActiveYield calibration locationActiveYield calibration location
ActiveYield InformationActiveYield Information

ActiveYield is available for model year 2016 through model year 2019 S760, S770, S780, and S790 Combines and requires the 4600 CommandCenter™ Display, GreenStar™ 3 2630 Display, or GreenStar 3 CommandCenter. Additionally, a StarFire 3000 or 6000 Receiver must be installed on the combine with the TCM calibrated for ActiveYield to detect machine pitch correctly. Manual yield calibration is not required as each crop has a built-in default value.

Harvest Doc™ system yield data collected by an ActiveYield system is only compatible with the John Deere Operations Center. John Deere does not guarantee compatibility of ActiveYield collected documentation with John Deere APEX™ software or third-party software systems.

Ladder Extension

230 mm Bolt-on Single Tire Platform - BXE10121

330 mm Bolt-on Single Tire Platform - BXE10122

Dual Tire Extension - BXE10120

Long Length Ladder  - BXE10420

Medium Length Ladder - BXE10421

Short Length Ladder - BXE10422

Machine Optimization Technology

Active Terrain Adjustment is a system that enhances grain quality and reduces grain loss when harvesting on ascending or descending hills. The feature automatically adjusts the combine’s sieve and chaffer openings and carefully controls the cleaning fan speed, stabilizing tailings levels and ensuring a clean grain tank sample.

 

Feature benefit:

  • Achieves same loss level as on level land conditions (on hills up to 10 degrees)

  • Tailings reductions by up to 35 percent on 8-12-degree inclines

  • Automatic settings adjustments on hills

Active Terrain Adjustment slopeActive Terrain Adjustment slope

Functionality:

 

Order Active Terrain Adjustment as a factory-installed option or as an attachment for field installation on model year 2016 machines and newer (PIN 785000 -). The feature can be used in both coarse and small grains in all terrain, but will excel especially on hills.

Active Terrain Adjustment pitch sensorActive Terrain Adjustment pitch sensor
Active Terrain Adjustment cleaning fan actuatorActive Terrain Adjustment cleaning fan actuator

When the machine starts an uphill climb, Active Terrain Adjustment will slow the cleaning fan down and open the chaffer and sieve elements. As the machine descends a hill, the cleaning fan speed will increase and the chaffer and sieve elements will close to decrease grain loss and prevent shoe loading.

ICA2 Retrofit Bundle for S780 and S790 Combines - BXE11035

Mirrors

Miscellaneous

105-mm (4-in.) Axle Spacer - BH92136

12 In. (300 mm) Axle Spacer  - HXE71480

16 In. (400 mm) Axle Spacer - HXE71479

165-mm (6.5-in.) Axle Spacer - BH92139

S690 Combine with manual grain tank extensionsS690 Combine with manual grain tank extensions

S680 and S690 Combines are equipped with manual-folding grain tank extensions and fewer covers in base equipment. Power-folding grain tank extensions/covers with a folding grain tank loading auger is available as optional equipment. The 400-bu manual-fold grain tank extension attachment allows for the conversion of power-folding covers to manual grain tank extensions.

454-mm (18-in.) axle spacer - BH92142

6 in. (155 mm) Axle Extension - BH92115

ActiveYield delivers automatic yield calibrations to the operator without spending time manually performing yield calibrations.

Feature benefit:

  • Simplified yield calibrations for improved uptime in the field
  • Simplified data collection for use during and after harvest
#

Functionality:

ActiveYield eliminates time-consuming manual yield calibrations and replaces them with automated sensors that calibrate the machine by measuring the grain as the tank fills. This enables decisions to be made in real time without leaving the cab.

ActiveYield sensors in grain tankActiveYield sensors in grain tank

When the ActiveYield option is enabled and the Terrain Compensation Module (TCM) in the StarFire™ 3000 or StarFire 6000 Receiver has been calibrated, ActiveYield is ready to go to work. As grain is harvested and enters the tank, the three sensors within the grain tank collectively measure the grain as it piles over the cross auger covers. If all conditions are acceptable (header and separator on, grain is flowing, and machine level is within 4 degrees) load collection occurs from 900 through 3000 kg (2000 through 6600 lb).

Any pitch and roll of more than 4 degrees from center during load collection will cause the system to reject that load due to the grain pile shifting in the tank. A new calibration load starts once grain is below the sensors on the cross auger covers.

Stored calibration loads are replaced by new ones as the system continues to collect data. The system may be disabled at any time by accessing the moisture setup page and unchecking the ActiveYield box if manual yield calibration is desired.

ActiveYield calibration locationActiveYield calibration location
ActiveYield InformationActiveYield Information

ActiveYield is available for model year 2016 through model year 2019 S760, S770, S780, and S790 Combines and requires the 4600 CommandCenter™ Display, GreenStar™ 3 2630 Display, or GreenStar 3 CommandCenter. Additionally, a StarFire 3000 or 6000 Receiver must be installed on the combine with the TCM calibrated for ActiveYield to detect machine pitch correctly. Manual yield calibration is not required as each crop has a built-in default value.

Harvest Doc™ system yield data collected by an ActiveYield system is only compatible with the John Deere Operations Center. John Deere does not guarantee compatibility of ActiveYield collected documentation with John Deere APEX™ software or third-party software systems.

Chopper Drive Shielding - BXE10357

Deflector - PowerCast Tailboard - KXE10121

Distribution Kit - Standard Flex Residue - KXE10148

Driveshaft bundle, S-Series w/ No Axle Spacer - BH84580

Dyna-Flo Plus Chaffer - AXE48125

Enhanced single-point latching systemEnhanced single-point latching system

John Deere’s single-point header latching system provides combine operators a fast and easy method for connecting all front-end equipment. One easy motion of the lever connects the electrical and hydraulic circuits along with header retaining pins.

  • No wrenches are required to complete the header-combine connection
  • Reduces the time required to change over headers, so there is more time available for harvesting
  • More convenient to remove headers for transport or storage

The enhanced single-point latching system, starting in model year 2016, will include a valve assembly mounted to all platform and corn head back sheets. These assemblies will include an orifice valve unique to the header type as well as a pressure override valve. Together, these ensure optimum performance and reliability of header hydraulic functions.

 

Compatibility for prior headers or combines to model year 2016 equipment is provided by attachments specific to the header and combine being used. Refer to the chart below for compatibility information.

 

Six different attachments cover the compatibility between new and used combines and front-end equipment. The attachments are BXE10667, BXE10666, BXE10668, BXE10670, BXE10697, and BXE10669.

#
#
Enhanced single-point latching systemEnhanced single-point latching system

John Deere’s single-point header latching system provides combine operators a fast and easy method for connecting all front-end equipment. One easy motion of the lever connects the electrical and hydraulic circuits along with header retaining pins.

  • No wrenches are required to complete the header-combine connection
  • Reduces the time required to change over headers, so there is more time available for harvesting
  • More convenient to remove headers for transport or storage

The enhanced single-point latching system, starting in model year 2016, will include a valve assembly mounted to all platform and corn head back sheets. These assemblies will include an orifice valve unique to the header type as well as a pressure override valve. Together, these ensure optimum performance and reliability of header hydraulic functions.

 

Compatibility for prior headers or combines to model year 2016 equipment is provided by attachments specific to the header and combine being used. Refer to the chart below for compatibility information.

 

Six different attachments cover the compatibility between new and used combines and front-end equipment. The attachments are BXE10667, BXE10666, BXE10668, BXE10670, BXE10697, and BXE10669.

#
#

Extra-Fine-Cut Chopper with American Power Conversion (APC) Outlet - BXE10170

Flex Residue Straw Spreader with Integrated Chaff Spreading, In-Cab Variable, Single Speed Control - BXE10358

Perforated and Clean Grain Doors - BH90075

The large tool cabinet is available on model year 2019 and newer combines models.

  • Integrated design can fold away on the left-hand side of the combine with a hinge at ground level, so the toolbox does not have to be completely removed from the machine.
  • 117-L (4.1-cu ft) of storage on two decks
  • Compartment can be locked with a key
Two tool cabinet decksTwo tool cabinet decks
Tool cabinet storage spaceTool cabinet storage space

Operator's Station

Retrofit Kit for Foot Pegs - KXE10454

Ash tray and cigarette lighter attachment for S-Series cabs

Radio

Rear Axle With 2-Speed, 4-Wheel Drive

Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder.

 

Please reference the following documents for more detailed information.

S-Series tire compatibility and spacing chart

Axle spacer chart

Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder.

 

Please reference the following documents for more detailed information.

S-Series tire compatibility and spacing chart

Axle spacer chart

Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder.

 

Please reference the following documents for more detailed information.

S-Series tire compatibility and spacing chart

Axle spacer chart

S700 rear-wheel assist motorS700 rear-wheel assist motor
Continue harvesting, even in muddy conditionsContinue harvesting, even in muddy conditions

Feature benefit:

  • Allows harvest to continue in muddy field conditions
  • Provides increased maneuverability and steering when ground conditions are wet or slick
  • Increases ground drive torque that may be needed when harvesting on slopes
  • Two-speed feature provides versatility to maximize harvest productivity when maximum ground drive torque or faster ground speed is needed.

 

Functionality:

Specifications of the 2294-cc (140-cu in.) 4WD system include:

  • In the slow-speed mode, the system provides a maximum of 2294-cc (170-cu in.) displacement per motor for maximum (high-torque) rear-wheel assist.
  • In the high-speed mode, the system provides 1147 cc (70 cu in.) of displacement for (low-torque) rear-wheel assist and faster ground speed capability.

On all ProDrive™ transmission machines, low-speed 4WD engagement is limited to 10 km/h (6.2 mph) and high-speed 4WD engagement is limited to 15.9 km/h (9.9 mph) with maximum speed up to 20 km/h (12.4 mph).

Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder.

 

Please reference the following documents for more detailed information.

S-Series tire compatibility and spacing chart

Axle spacer chart

Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder.

 

Please reference the following documents for more detailed information.

S-Series tire compatibility and spacing chart

Axle spacer chart

Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder.

 

Please reference the following documents for more detailed information.

S-Series tire compatibility and spacing chart

Axle spacer chart

Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder.

 

Please reference the following documents for more detailed information.

S-Series tire compatibility and spacing chart

Axle spacer chart

Enhanced single-point latching systemEnhanced single-point latching system

John Deere’s single-point header latching system provides combine operators a fast and easy method for connecting all front-end equipment. One easy motion of the lever connects the electrical and hydraulic circuits along with header retaining pins.

  • No wrenches are required to complete the header-combine connection
  • Reduces the time required to change over headers, so there is more time available for harvesting
  • More convenient to remove headers for transport or storage

The enhanced single-point latching system, starting in model year 2016, will include a valve assembly mounted to all platform and corn head back sheets. These assemblies will include an orifice valve unique to the header type as well as a pressure override valve. Together, these ensure optimum performance and reliability of header hydraulic functions.

 

Compatibility for prior headers or combines to model year 2016 equipment is provided by attachments specific to the header and combine being used. Refer to the chart below for compatibility information.

 

Six different attachments cover the compatibility between new and used combines and front-end equipment. The attachments are BXE10667, BXE10666, BXE10668, BXE10670, BXE10697, and BXE10669.

#
#

Parts Assembly - Box of Final Drive Axle Extensions - BH81747

Residue Disposal

APC Corn Kit - KXE10135

Adjustable Finger Rakes - KXE10296

Corn Kit OSB Cover - KXE10303

Deflector Windrow Convergence Kit - AH210317

Fine Cut Chopper with Standard VTB Outlet - BXE10172

Fine Cut Chopper with Standard VTB Outlet - BXE10660

Flex Residue Straw Spreader with Integrated Chaff Spreading, In-Cab Variable, Single Speed Control - BXE10181

Hydraulic Plus Electric for Advanced PowerCast Fine-Cut and Extra-Fine-Cut (FC and XFC) - BXE10817

Hydraulic Plus Electric for Advanced PowerCast Fine-Cut and Extra-Fine-Cut (FC and XFC) - BXE10893

Hydraulics and electrics for spreadersHydraulics and electrics for spreaders
#

The twin-disc straw spreader system uses two large impellers to ensure uniform distribution of material from the separator and cleaning system. The spreader is recommended for use when tillage practices do not dictate fine sizing of crop residue.

 

Straw spreader options:

 

1. Standard straw spreader

  • This spreader is not recommended for use with greater than 9.14-m (30-ft) platforms 

2. Widespread straw spreader (not available on the S650)

  • This spreader is recommended for use with 9.14-m (30-ft) to 12.2-m (40-ft) platforms
  • On the S660-S690 speeds of the spreader can be independently controlled
  • This spreader is not recommended for use in rice applications
Hydraulics and electrics for spreadersHydraulics and electrics for spreaders
#

The twin-disc straw spreader system uses two large impellers to ensure uniform distribution of material from the separator and cleaning system. The spreader is recommended for use when tillage practices do not dictate fine sizing of crop residue.

 

Straw spreader options:

 

1. Standard straw spreader

  • This spreader is not recommended for use with greater than 9.14-m (30-ft) platforms 

2. Widespread straw spreader (not available on the S650)

  • This spreader is recommended for use with 9.14-m (30-ft) to 12.2-m (40-ft) platforms
  • On the S660-S690 speeds of the spreader can be independently controlled
  • This spreader is not recommended for use in rice applications

Hydraulic Plus and Electric for PowerCast - BXE10364

Knife Kit - KXE10363

PowerCast Tailboard - BXE10174

Premium Chopper Vane Kit for 7.6m (25 Ft.) Spread Width - AH219763

Standard Deflectors - BXE10179

Manual vane tailboardManual vane tailboard
Manual vane tailboard mountedManual vane tailboard mounted

The manually adjustable vane tailboard design provides a residue spread pattern for platform cut widths up to and including 9.14 m (30 ft).

 

The manually adjustable vane tailboard allows simple vane angle adjustments from the ground. Manually adjust the vane position, as required, to meet the desired spread width.

Straw Chute Plugging Kit - KXE10287

Straw Spreader Parts, Extra Wide, for use on Twin Disk, Wide Spread with Integrated Chaff Spreader - BXE10648

Straw chopper knife bushing kit - KXE10257

XFC Chopper Vane Kit for 7.6m (25 Ft.) Spread Width - AH223773

Separation

Heavy Duty Grate - Separator Covers (Set of 20) - BXE10646

Separator Grate Covers (Set of 4) - BXE10645

Separator Kit - SEPARATOR KIT, BEATER, 8-WING TOUGH - KXE10347